Stiebel Eltron DHC-E 8/10 Point-of-Use Tankless
Stiebel Eltron DHC-E 8/10
Our Price: CDN$375.70
Choose Refurbished 2nd Gen (Grey)
Limited Quantity of Factory Refurbished units available.
Save an additional $96.7!
- more info -
The Stiebel Eltron DHC-E 8/10 combines the DHC-E 8 and DHC-E 10 into a single unit. Changing a jumper during installation allows this unit to act as either an 8 KW or 10 KW unit.
The Stiebel Eltron DHC-E series tankless water heaters are the most advanced point-of-use tankless water heaters on the market today. The DHC-E 8 and DHC-E 8/10 both feature the same industry-leading thermostatic temperature control and flow and temperature based power modulation technology found in Stiebel Eltron's flagship Tempra whole house heaters. Set the desired temperature on the front of the unit and enjoy water temperatures between 86° (30°C), and 140° (60°C). Change the desired temperature at anytime. Advanced microprocessor technology ensures that the water temperature never deviates from the set point.
By producing hot water on demand only as it is being used, the DHC-E 8/10 is extremely energy efficient. A sophisticated water flow sensor recognizes when hot water is being used and when it has been turned off, so the unit will activate and deactivate automatically so it only runs when you are actually using water. This eliminates standby thermal heat losses associated with traditional tank type water heaters. Accordingly, you can expect to see a significant cost reduction over the operating cost of a conventional water heater.
|Maximum Flow Rate in Gallons Per|
Minute at 105F Output Temperature
|Incoming Water Temp:||Flow Rate (GPM)|
|40F||0.75 / 1.00 GPM|
|45F||0.82 / 1.09 GPM|
|50F||0.89 / 1.19 GPM|
|55F||0.98 / 1.31 GPM|
|60F||1.09 / 1.45 GPM|
|65F||1.22 / 1.63 GPM|
|70F||1.40 / 1.87 GPM|
|75F||1.63 / 2.18 GPM|
brochure for temp rise chart based on 208v input.
and Flow-Based Power Modulation!
The DHC-E 8/10 point-of-use tankless water heater is ideal for bathroom sinks, kitchens, commercial washrooms, and a wide range of other point of use applications. Due to its small size, the Stiebel Eltron DHC-E 8/10 conveniently fits directly under the sink or adjacent cupboard or closet, so it delivers hot water to the sink almost instantly. By locating the heater right near the point-of-use, you can also eliminate thermal heat loss commonly associated with long pipe runs. If the DHC-E 8/10 can supply all of the hot water needs for the room, in new construction applications, you also eliminate the need to run a hot water line all the way from the main central water heater which can save you significant money in plumbing and material cost.
The Stiebel Eltron DHC-E 8/10 is not recommended for whole house use. For more information on whole house models, see our Stiebel Eltron Tempra Series Whole House Tankless Water Heaters.
Stiebel Eltron DHC-E 8/10 Tankless Water Heater Specifications
|Thermostatically Controlled?||Yes, temperature control and full power modulation based on flow rate and incoming water temperature.|
|KW||9.6 KW @ 240v / 7.2 KW @ 208v|
|Voltage:||208 - 240 volts / single phase / 50 - 60 Hz|
|Max. Amps:||40 AMPS @ 240v / 35 AMPS @ 208v|
|Breakers Required:*||1 x 40 AMP breaker @ 240V
or 1 x 35 amp breaker at 208V (depends on local codes)
|Wiring:*||Minimum #8 AWG Copper (depends on local codes)|
|Dimensions:||14.25 x 7.9 x 4.1" (36 x 20 x 11 cm)|
|Weight:||5.9 lbs (2.7 KG)|
|Pipe Fittings:||1/2" NPT|
|Activation Flow Rate:||0.26 GPM / 1.0 LPM|
|Max. Water Pressure:||150 psi|
|Warranty:||Manufacturer's 3 Year Warranty|
|Safety:||ETL Listed (US / Canada)|
|Protection:||microprocessor-based thermostatic temperature control (flow rate and temperature modulating) with thermal hi-limit cut-out switch|
* Breaker size and wire gauge must meet all applicable local, state, provincial, and national electrical codes for your area - these are only guidelines that will apply to most installations. Please consult your electrician for more details.