Stiebel Eltron Tempra 20 Trend Electric Tankless Water Heater
Stiebel Eltron Tempra 20 Trend
Our Price: CDN$748.75
You save: $391.25
Choose Refurbished 2nd Gen (Grey)
Limited Quantity of Factory Refurbished units available.
Save an additional $85.75!
- more info -
The new Tempra 20 Trend replaces the discontinued Tempra 20B.
It offers all the same features of the Tempra 20B, with a new digital display, in a modern white powder-coated case.
The 19.2KW Stiebel Eltron Tempra 20 Trend is configured for climates where the incoming water temperature is above 60°F, and is suitable as a whole house water heater in the southern U.S. and in some warmer northern climates. It is also a popular choice for summer use vacation properties in northern climates where the electrical service does not permit the installation of a larger model. It is also frequently used for small commercial tankless water heater applications where low flow rates are required.
|Maximum Flow Rate in Gallons Per|
Minute at 105F Output Temperature
|Incoming Water Temp:||Flow Rate (GPM)|
brochure for temp rise chart based on 208v input.
Like all Tempra Series tankless water heaters, the Tempra 20 features a convenient dial selector which allows you to set the desired output water temperature at any level between 86 and 140F (30 and 60C). Most importantly, it is one of the only tankless water heaters on the market that features a true thermostatic temperature control and full power-modulation based on both the incoming water temperature and the water flow rate. In layman's terms, the Tempra 20 will automatically sense the water flow rate and temperature, calculate how much power is needed to do the job, and will apply exactly that much power so it can precisely maintain the desired output temperature regardless of whether the flow rate changes or not. The result is the most precise temperature control of any tankless water heater on the market today!
Stiebel Eltron Tempra 20 Trend Specifications
|Thermostatically Controlled?||Yes, temperature control and full power modulation based on flow rate and incoming water temperature.|
|KW||19.2 KW @ 240v / 14.4 KW @ 208v|
|Voltage:||208 - 240 volts / single phase / 50 - 60 Hz|
|Max. Amps:||80 AMPS @ 240v / 70 AMPS @ 208v|
|Breakers Required:*||2 x 40 AMP breakers (depends on local codes)|
|Wiring:*||Minimum 2 x #8 AWG Copper (depends on local codes)|
|Dimensions:||16.6 x 14.5 x 4.6" (42 x 36.7 x 11.6 cm)|
|Weight:||15.4 lbs (7.3kg)|
|Pipe Fittings:||3/4" NPT|
|Activation Flow Rate:||0.50 GPM / 1.9 LPM|
|Max. Water Pressure:||150 psi|
|Warranty:||Manufacturer's 3 Year Warranty|
|Safety:||ETL Listed (USA & Canada) - complies with both US and Canadian safety standards including ANSI/UL499 and CSA-E335-1/3E-94.|
|Protection:||microprocessor-based thermostatic temperature control (flow rate and temperature modulating) with thermal hi-limit cut-out switch monitoring each heating module|
Please note: A minimum 125 AMP household electrical service is highly recommended and will likely be required to install this model. If you are unsure of your electrical capacity in your home, please consult your electrician or contact us for assistance before ordering.
* Breaker size and wire gauge must meet all applicable local, state, provincial, and national electrical codes for your area - these are only guidelines that will apply to most installations. Some codes require use of electrical sub-panel for installation, especially when heater is not mounted within line-of-sight of the main electrical panel. Wiring should be sized to maintain a voltage drop of less than 3% under load. Please consult your electrician for more details.